Wireless Tips
Wireless not working? Try these tips!
Look For A Physical Button | All too frequently, one will spend a whole bunch of time trying to configure a seemingly non-functional wireless only to realize later that there was a much simpler solution. First, look for a button or switch or combination of keys to activate/deactivate the wireless. For example, is there a button above the keyboard? a switch on the side? maybe Fn + F5 turns the wireless on and off? A wireless antenna icon on the laptop is also a good clue, especially if it is illuminated. |
For these wireless cards: Intel PRO/Wireless 2200BG and 2915ABG using the lpw2200 driver | The indicator light for the Wifi on/off switch does not come on.This confuses quite a few customers (who have turned off their Wifi but do not know how to verify that they have done so). The solution can be found at the following link With thanks to Levi for the fix. |
BIOS Trickery | Check out the BIOS settings. Sometimes there is an option in BIOS to disable/enable a mini-PCI or Wireless device. If so, make sure that you enable it. |
lspci Is Your Friend | The lspci command is a utility for displaying information about all PCI buses in the system and all devices connected to them. It will tell you about your wireless card, if there is one installed. In particular, it will tell you whether your wireless card has a Broadcom chipset (which, if it does, you'll need to install some stuff - see below). The following example is the output from running lspci and it demonstrates that the Wireless card has a Broadcom chipset (see the words "Broadcom" and "Wireless" in the same line?).
09:00.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03) |
ifconfig: Am I Connected? | The ifconfig command configures a wired network interface. It is a useful command for determining whether or not you're connected to a network AND which network interface is being used to connect (i.e. whether you're connected to a wireless or wired network).
eth0 Link encap:Ethernet HWaddr 08:00:46:0E:8C:D8 inet addr:192.168.2.252 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:46ff:fe0e:8cd8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3588 errors:0 dropped:0 overruns:0 frame:0 TX packets:624 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1050713 (1.0 MiB) TX bytes:111359 (108.7 KiB) This example shows that interface eth0 is connected (because it shows an inet address). To determine whether eth0 is the wired or wireless interface, use iwconfig |
iwconfig: No Wires! | The iwconfig command configures a wireless network interface. It is a useful command for determining which interface is being used for wireless networking.
eth0 no wireless extensions. eth1 radio off ESSID:"" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power=off Sensitivity=8/0 Retry limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 The above example shows 3 important things: (1) that your wireless interface is eth1, (2) that eth0 is your wired network (because it reads "no wireless extension"), and (3) that your wireless is turned off ("radio off"). When you see "radio off" this generally means there's a physical button somewhere on the laptop that is currently in the off position. Note this has been somewhat superceeded by the iw command which is lower level. Sometimes iwconfig will fail because of e.g. configuration issues but iw will still give useful output. If you switched on the wireless and then ran iwconfig you might see something like this: eth1 IEEE 802.11g ESSID:"freegeek" Mode:Managed Frequency:2.422 GHz Access Point: 00:14:BF:2B:41:1D Bit Rate:54 Mb/s Tx-Power=20 dBm Sensitivity=8/0 Retry limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=93/100 Signal level=-34 dBm Noise level=-89 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:4 Note that the ESSID is "freegeek." This means that you're connected to the Free Geek wireless network. |
dhclient | The dhclient command will look for a server that will give your laptop a network address. Run this command as a super-user (sudo).
|
Broadcom Chipset | So you've discovered that your wireless card has a Broadcom chipset, eh? Try these steps:
sudo apt-get install b43-fwcutter |
Try a Newer liveCD | Normally we use Ubuntu 10.04 on all our systems, but some newer wireless cards are not supported in this version. Use a live CD of the latest Ubuntu version (currently 11.04), and see if the card works. |
Xubuntu 12.04 BCM4311 | $> sudo apt-get purge bcmwl-kernel-source broadcom-sta-common broadcom-sta-source
$> sudo apt-get install b43-fwcutter firmware-b43-installer |
Try Using ndiswrapper | If the card does not work natively under Linux you can always try using the windows driver with ndiswrapper. |
Try Editing Network Interfaces | sudo gedit /etc/network/interfaces
Then remove all lines but lo. |
Tesing for a wireless connection |
If your wireless network manager cannot see the RF signal from a wireless AP and it's corresponding information necessary for a wifi client to connect to it, ip connectivity is not the issue. You have to have radio (physical layer) connectivity before you can get ip layer connectivity. The only real test here is to use a low level wireless tool such as iw. If when you run the command "iw wlan0 scan", you don't get results like below there's a RF level communication problem between the radio in your wifi card and the radio in the wireless AP. iw wlan0 scan BSS 00:07:85:b3:a1:5b (on wlan0) TSF: 5969236565582 usec (69d, 02:07:16) freq: 2422 beacon interval: 100 capability: ESS ShortPreamble (0x0021) signal: -61.00 dBm SSID: freegeek Supported rates: 1.0* 2.0* 5.5* 11.0* DS Parameter set: channel 3 BSS 00:18:39:70:15:3d (on wlan0) TSF: 23167367530426 usec (268d, 03:22:47) freq: 2437 beacon interval: 100 capability: ESS Privacy ShortSlotTime (0x0411) signal: -82.00 dBm SSID: TECH-NET-EZ Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 DS Parameter set: channel 6 ERP: Barker_Preamble_Mode Extended supported rates: 6.0 9.0 12.0 48.0 You can also use iwlist scanning which gives somewhat friendlier output but is not as reliable always. iwlist |
Are we really desperate yet? | Sometimes a more mainstream wireless card could be the answer or perhaps a loose antenna connection could be the culprit.
Don't forget that wireless isn't magic. It isn't going to work if there are lots of walls/trees etc in the way or the access point is too far away. |