Difference between revisions of "SCSI Hard Drive Triage"

Latest revision as of 14:51, 4 December 2012

Currently, SysEval is told to bring all SCSI HDs 146GB & larger to HD Incoming in the TARDIS.

Triage Chart

This is a graph with borders and nodes. Maybe there is an Imagemap used so the nodes may be linking to some Pages.

SCSI Hard Drive Testing

@@ Line 1: / Line 1: @@
 __NOTOC__
-SCSI Hard Drive sorting is done in [[Advanced Test]].
+Currently, SysEval is told to bring all SCSI HDs 146GB & larger to HD Incoming in the TARDIS.
-== Start ==
-copied from ps triage, not done yet.
-Create a temporary place for two piles:
-* Keep
-* Recycle
-Follow the triage flow chart below to determine which pile to put the power supply in. You will need to test some power supplies to complete this task.
 == Triage Chart ==
 <graphviz>
-   digraph POWERSUPPLYTRIAGE {
+   digraph SCSIHDTRIAGE {
    node [fontname="Helvetica", fontsize="11"]
    edge [fontname="Helvetica"]
-  at        [label="Is it an AT?\n(not an ATX)"]
    start     [label="START HERE", shape="box", style="bold"]
-   switch    [label="Does it have an\nintact SWITCH?"]
+   inspect   [label="Visually inspect it:\nAre there any signs of damage?"]
-   shape     [label="Is it the same shape and size\n as the power supply marked 'EXAMPLE'?\nLittle metal rails don't count as different;\nexternal fans do."]
+   size      [label="Is it 146 GB or larger?"]
-  compaq    [label="Does it say 'COMPAQ' on its label?"]
+   keep      [label="KEEP"  shape="box", style="bold"]
-  broken    [label="Is it broken?\nDoes it have clipped cords or an open case?\nDid somebody write 'BAD' on it?"]
+   recycle   [label="RECYCLE" shape="box", style="bold"]
-  test      [label="TEST IT\nDoes it work?"]
-  inspect   [label="VISUALLY INSPECT IT\nAre there scorched connectors?"]
-   keep      [label="KEEP."  shape="box", style="bold"]
-   recycle   [label="RECYCLE" shape="box", style="bold"]
-   start -> at
+   start ->   inspect
-   at -> switch [label="YES"]
+   inspect -> recycle [label="YES"]
-   at -> shape [label="NO"]
+   inspect -> size [label="NO"]
-  switch -> keep [label="YES"]
-   switch -> recycle [taillabel="NO"]
-  shape -> broken [label="YES"]
-  shape -> recycle [taillabel="NO"]
-   broken -> recycle [taillabel="YES"]
+   size -> keep [label="YES"]
-   broken -> inspect [label="NO"]
+   size -> recycle [label="NO"]
-  inspect -> compaq [label="NO"]
-  inspect -> recycle [label="YES"]
-  compaq -> recycle [label="YES"]
-  compaq -> test
-  test -> recycle [label="NO"]
-  test -> keep [label="YES"]
    }
 </graphviz>
-== Testing Power Supplies ==
+[[SCSI Hard Drive Testing]]
-Use a standard ATX power supply tester for a 20 pin ATX power supply. If you have a 24 pin ATX power supply, send it to advanced testing instead.
-For each power supply that needs to be tested, do these things:
-# Plug each power supply into outlet
-# If there is a rear power supply switch, make sure it is turned on.
-# Connect the tester to the 20 pin ATX connector
-#* Check lights (all lights on is good, but it is also OK if the -5V light is off)
-# Connect the tester to the 4 pin ATX connector
-#* Check to see if the +12V light is on
-== What to do when done, where to put them ==
-; Keepers
+[[Category: Advanced Testing]]
-: Mark them '''small smiley face''' in a corner on the side where the wires come out with a sharpie
-: Take them to the warehouse and put them in the POWER SUPPLIES TO KEEP location
-; Recycle
-: Mark them '''LARGE frowny face''' somewhere with a sharpie
-: Take them to the warehouse and put them in the POWER SUPPLIES TO RECYCLE location
-[[Category: Advanced Test]]
+<!-- comment here -->

Difference between revisions of "SCSI Hard Drive Triage"

Latest revision as of 14:51, 4 December 2012

Triage Chart

Navigation menu

Search