MacBuild Intel Checklist

Build

Steps	Notes/Detailed Instructions	Done
Check for blown capacitors (if system can be easily opened)	Visually inspect motherboard capacitors for bulges/leaks. If you find one, check with your instructor.
Make sure that covers are available for open bays	If covers are missing, check parts storage for replacements
Install battery	Pay attention to correct position; look for '+' by battery holder
Install hard drive (if it has not been wiped in the system)	Refer to MacBuild Spec Sheet for appropriate size
Install/swap RAM	If the system has a built-in display, remember to swap out any old untested memory in it for new tested memory. Refer to MacBuild Spec Sheet for appropriate amount, but all systems should have a minimum of 512MB of RAM.
Clean/dust inside	If necessary
Attach keyboard/mouse, monitor, network cable, and power cord (as necessary)
Clear the PRAM	While starting up, hold the Option+Apple+p+r keys. Continue holding the keys until the system chimes three times. Release the keys after the third chime is heard.
Set the system clock and NVRAM in Open Firmware	While starting up, hold the Option+Apple+o+f keys. Release the keys when the Open Firmware prompt comes up. Run the following command: decimal dev rtc [sec min hour day month year] set-time All values aside from the year should be two-digit numbers in 24-hour format. The year should be a four-digit number. Additionally, the clock needs to be set to UTC, so remember to add 7 hours to the current time if on regular time or 8 hours during Daylight Saving Time. For example, to set the clock to 1:58 PM on September 18th, 2009, the command would be decimal dev rtc 00 58 20 18 09 2009 set-time To reset the NVRAM type the following commands in the specified order: reset-nvram set-defaults reset-all The system will reboot after the reset-all command is entered.
Install Ubuntu	Please note that any values not explicitly defined here (HTTP proxies and such) should be left blank. Make sure network cable is attached Insert Ubuntu CD Use 8.04 for iMac G5s Use 9.04 for all other systems Start up the system while holding the C key on the keyboard At boot: prompt, press Enter; eventually the install screen will appear Select English as the language for the installation and United States as the country Enter No for keyboard detection, and select USA for all keyboard language options If prompted for which network device to use, select the wired network When prompted for a hostname, delete the current entry and enter macbox in its place Select Pacific as the time zone When prompted for HD partitioning, select the Guided - use entire disk option, and confirm the HD the changes will be made to (there should only be one option available unless there are multiple HDs in the system) When asked about writing the changes to disk, select Yes At this point, the base system will begin installing, so prepare to wait for a few minutes When prompted for the user's full name, enter oem When prompted for a username for the account, enter oem When prompted for a password, enter freegeek. You will be asked to verify the password after entering it. Enter freegeek again. If the passwords don't match, it will prompt you for a password again If asked to provide a HTTP proxy, leave it blank and press Enter If asked to download additional language support, select Yes If asked to encrypt the user's home directory, select No When asked if the system clock is set to UTC, select Yes When installation is complete, select the Continue option to reboot the system
Start up Ubuntu	Let the system use its default options in the bootloaders during the startup process If the system has problems starting up, refer to the Special Configurations list
Verify hardware in the system	To verify the hardware in a system, open up a terminal and run: sudo lshw|less This runs a command called lshw (which stands for "list hardware") and sends the output to another command called less, which is a simple reader that allows you to scroll through lshw's output. The items to pay attention to are: Amount of system memory You should be able to find this under the memory heading in lshw. It should be the same as the physical amount of memory in the system. Type of optical drive This can be found under the cdrom heading in lshw. To determine the actual capability of the drive, search for the information under product in Google. Presence of wireless card This should be under one of the network headings. You should look for an entry that mentions something about "Wireless interface" or "Broadcom". If that exists, the system has a wireless card.
Set up the environment and install extra apps	Add the Terminal to the panel so it can be launched quickly If the machine has a DVD drive, open up a terminal and run: sudo apt-get install vlc If the machine has a wireless card, open up a terminal and run: sudo apt-get install b43-fwcutter Restart the system after installing b43-fwcutter in order to get the change working properly.
Test USB ports	Plug in a USB mouse See that the cursor moves and can interact with things Repeat with all USB ports If any port doesn't work, the machine should be recycled
Test CD/DVD data and sound	Insert, play, and eject a music CD Insert data CD, inspect directory contents If machine has a DVD drive: insert a data DVD, inspect directory contents insert a video DVD and play it using vlc If machine has a CD-RW or DVD-RW, use brasero to erase a CD-RW disk, and create/burn a new data project. Note: Brasero has problems with versions of Ubuntu before Karmic (9.10). For Hardy (8.04LTS) and Jaunty (9.04) you may want to install and use k3b instead: sudo apt-get install k3b
Check if wireless works (if the system has a wireless card)	Use Network Manager to see if you can connect to Free Geek's wireless network. If you can, the wireless card works.
Check for software updates	There are a few ways to do this: From the desktop, go to System -> Administration -> Update Manager From the command line, run: sudo apt-get update sudo apt-get upgrade Install all updates if any are found
Generate "printme" report for system	In a terminal, generate a lshw XML file for the printme process sudo lshw -xml > printme.xml Open a web browser and go to http://data/spec_sheets/new Fill out the form with the following: Enter your volunteer ID in the Volunteer ID field Job should be changed to Builder System ID should be left blank Type should be changed to Apple Keeper label type should be set to No Sticker Notes should include the following information: Version of Ubuntu installed Any components that show up in lshw (modems, certain wireless cards) that aren't supported by Ubuntu should be listed Any special issues the machine has Whether the computer is covered or not Upload the XML file, and print out the report When asked where to print the report, select the Print to File option at the top of the printer list in the Print window Select PDF as the output format, and save the file to the desktop as build_printme.pdf
Power down the system and place on the QC shelf

This is Roy's simplified version of a checklist for Mac desktop build:

Build

Steps	Notes/Detailed Instructions	Done
Attach keyboard/mouse, monitor, network cable, and power cord (as necessary)
Clear the PRAM	While starting up, hold the Option+Apple+p+r keys. Continue holding the keys until the system chimes three times. Release the keys after the third chime is heard and shift quickly to the Option+Apple+o+f keys.
Set the system clock and NVRAM in Open Firmware	While starting up, hold the Option+Apple+o+f keys. Release the keys when the Open Firmware prompt comes up. Run the following command: decimal dev rtc [sec min hour day month year] set-time All values aside from the year should be two-digit numbers in 24-hour format. The year should be a four-digit number. Additionally, the clock needs to be set to UTC, so remember to add 7 hours to the current time if on regular time or 8 hours during Daylight Saving Time. For example, to set the clock to 1:58 PM on September 18th, 2009, the command would be decimal dev rtc 00 58 20 18 09 2009 set-time To reset the NVRAM type the following commands in the specified order: reset-nvram set-defaults reset-all The system will reboot after the reset-all command is entered.
Install Ubuntu via the network	We are currently using a network installation of Ubuntu. To access this install, hold down the n key (for network) while the computer starts. As soon as the network icon starts blinking on the screen you may release the n key. At the first boot prompt enter an l (for linux) to install the current version of Ubuntu. The installation will stop at the keyboard selection. Accept the defaults (No or USA) for the next 3 screens and the installation will continue automatically. When prompted for a hostname, delete the current entry and enter macbox in its place When prompted for HD partitioning, accept the default and the rest of the installation will proceed automatically. The installation will take approximately 30 minutes and the computer will automatically reboot following the installation.
Start up Ubuntu	Log into the system using the username oem and password freegeek. If the system has problems starting up, refer to the Special Configurations list
Set up the environment and verify hardware in the system	Add the Terminal to the panel so it can be launched quickly. You can do this by dragging and dropping the terminal icon to the top task bar. To verify the hardware in a system, open up a terminal and run: sudo lshw This runs a command called lshw (which stands for "list hardware") The items to pay attention to are: Amount of system memory You should be able to find this under the memory heading in lshw. It should be the same as the physical amount of memory in the system. Type of optical drive This can be found under the cdrom heading in lshw. Presence of wireless card This should be under one of the network headings. You should look for an entry that mentions something about "Wireless interface" or "Broadcom". If that exists, the system has a wireless card. This is a good time to shut down the system and install additional memory or a wireless card if they are missing. Ubuntu will not run well with 256MB of memory and will sometimes generate errors that don't occur when 512MB or more memory is installed.
Test CD/DVD data and sound	Insert, play, and eject a music CD If machine has a CD-RW or DVD-RW, use brasero to erase a CD-RW disk, and create/burn a new data project. If machine has a DVD drive: insert a data DVD, inspect directory contents
Check if wireless works (if the system has a wireless card)	Use Network Manager to see if you can connect to Free Geek's wireless network. If you can, the wireless card works.
Generate "printme" report for system	Set up the printer by selecting System - Administration - Printing. When the printers window opens, select servers and click on the top box (access printers shared by other computers). Close the printing window. In a terminal, type printme Enter your volunteer ID in the Volunteer ID field Job should be changed to Builder System ID should be left blank Type should be changed to Apple Keeper label type should be set to No Sticker Choose whether the computer is covered or not Notes should include the following information: Version of Ubuntu installed Any components that show up in lshw (modems, certain wireless cards) that aren't supported by Ubuntu should be listed Any special issues the machine has When asked where to print the report, select the printer Double.
Power down the system, attach the printme sheet, and take to the store or place on storage shelf as appropriate.

QC (in progress)

Steps	Notes/Detailed Instructions	Done
Attach keyboard/mouse, monitor, network cable, and power cord (as necessary)
Verify that the splash screen works	When powering on the system, you should see the Ubuntu splash screen before the desktop finishes loading. It's fine if the colors are irregular, as long as something is displayed. If the splash screen doesn't work, go through the steps in the Special Configuration to enable it.
Verify hardware in the system	To verify the hardware in a system, open up a terminal and run: sudo lshw|less This runs a command called lshw (which stands for "list hardware") and sends the output to another command called less, which is a simple reader that allows you to scroll through lshw's output. The items to pay attention to are: Amount of system memory You should be able to find this under the memory heading in lshw. It should be the same as the physical amount of memory in the system. Type of optical drive This can be found under the cdrom heading in lshw. To determine the actual capability of the drive, search for the information under product in Google. Presence of wireless card This should be under one of the network headings. You should look for an entry that mentions something about "Wireless interface" or "Broadcom". If that exists, the system has a wireless card.
Test CD/DVD data and sound	Insert, play, and eject a music CD Insert data CD, inspect directory contents If machine has a DVD drive: insert a data DVD, inspect directory contents insert a video DVD and play it using vlc If machine has a CD-RW or DVD-RW, use brasero to erase a CD-RW disk, and create/burn a new data project. Note: Brasero has problems with versions of Ubuntu before Karmic (9.10). For Hardy (8.04LTS) and Jaunty (9.04) you may want to install and use k3b instead: sudo apt-get install k3b
Check if wireless works (if the system has a wireless card)	Use Network Manager to see if you can connect to Free Geek's wireless network. If you can, the wireless card works.
Check for software updates	There are a few ways to do this: From the desktop, go to System -> Administration -> Update Manager From the command line, run: sudo apt-get update sudo apt-get upgrade Install all updates if any are found
Verify printme notes	Locate the 'build_printme.pdf file on the desktop. Open it up and make sure that the notes written on the Build printme sheet accurately reflect the components and special issues with the system. If they are not accurate, please make any necessary changes when you create the printme printout for the QC process.
Generate "printme" report for system	Make sure you are on the local wired network Configure system so it can use network printers In a terminal, generate a lshw XML file for the printme process sudo lshw -xml > printme.xml Open a web browser and go to http://data/spec_sheets/new Fill out the form with the following: Enter your volunteer ID in the Volunteer ID field Job should be left as Quality Checker System ID should be filled in with the system ID listed in build_printme.pdf Type should be changed to Apple Keeper label type should be set to No Sticker Notes should include the following information: Version of Ubuntu installed Any components that show up in lshw (modems, certain wireless cards) that aren't supported by Ubuntu should be listed Any special issues the machine has Whether the computer is covered or not upload the XML file, and print out the report
Clean outside cover	Clean case monitor face, connector panel, keyboard, and mouse as well
Attach "printme" report to system
Bundle system with tested keyboard/mouse and power cord
Place system on the Outbound shelf