Difference between revisions of "Server Build Checklist"
Jump to navigation
Jump to search
Line 38: | Line 38: | ||
* '''Test USB ports''' (front and back), | * '''Test USB ports''' (front and back), | ||
* '''Test video ports''' (front and back), | * '''Test video ports''' (front and back), | ||
− | * '''Test network ports''' - at terminal: <code>'''ifconfig eth0 up'''</code>, <code>'''ifconfig eth1 up'''</code>, then <code>'''tail -f /var/log/syslog'''</code>, and when you plug and unplug the ethernet cable, you should see reasonable printouts. Ctrl-C to stop the <code>'''tail'''</code> command. | + | * '''Test network ports''' - at terminal: <code>'''ifconfig eth0 up'''</code>, <code>'''ifconfig eth1 up'''</code>, then <code>'''tail -f /var/log/syslog'''</code>, and when you plug and unplug the ethernet cable, you should see reasonable printouts. Ctrl-C to stop the <code>'''tail'''</code> command.<br><br> |
− | * '''QC Only:''' Remove any SATA/SAS drives and give them to your Instructor | + | ***'''QC Only:''' Remove any SATA/SAS drives and give them to your Instructor<br><br> |
− | + | '''Run printme:''' | |
− | + | *Boot from network | |
** Select printme from the network boot menu | ** Select printme from the network boot menu | ||
** Log in as guest | ** Log in as guest | ||
** Open a terminal | ** Open a terminal | ||
** Run printme | ** Run printme | ||
− | ** Answer all | + | ** Answer all questions and record anything else noteworthy in the notes section<br><br> |
− | Fill out the Server Specs sticker based on whether you are doing Build or QC: | + | '''Fill out the Server Specs sticker''' based on whether you are doing Build or QC: |
* '''For BUILD:''' | * '''For BUILD:''' | ||
** Put System ID on server specs sticker | ** Put System ID on server specs sticker | ||
− | ** Processor speed (GHz) | + | ** Number of physical processors and number of cores ''per'' processor |
− | ** | + | ** Processor speed (''GHz'') |
− | ** | + | ** Circle processor type (''Xeon, Opteron, Core 2, Other'') |
− | ** Number of included RAM sticks with their type, | + | ** Total amount of included RAM |
− | ** Number of hard drive bays | + | ** Total number of RAM slots on board |
+ | ** Number of included RAM sticks with their speed and size | ||
+ | ** Circle type of RAM (''DDR, DDR2, DDR3'') | ||
+ | ** Circle type of DIMM (''ECC, FB-DIMM, etc.'') | ||
+ | ** Number of hard drive bays | ||
+ | ** Circle hard drive bay type (''IDE, SCSI, SATA, SAS'') | ||
** Number and size of included hard drives | ** Number and size of included hard drives | ||
+ | ** Record anything notable, like Hardware RAID support, in the notes section | ||
** '''Do ''not'' print!''' Instead, put your Volunteer ID on a piece of tape on the system | ** '''Do ''not'' print!''' Instead, put your Volunteer ID on a piece of tape on the system | ||
* '''For QC:''' | * '''For QC:''' | ||
− | ** Confirm the accuracy of information already on the Specs sticker | + | ** Confirm the accuracy of information already on the Server Specs sticker |
− | |||
** Number and size of included hard drives | ** Number and size of included hard drives | ||
+ | ** Circle OS installed (none if hard drives removed) | ||
** Write the ''System ID#'' on a Server Tag sticker (small labels marked S1, S2, etc.) and stick it to the front face of the chassis. | ** Write the ''System ID#'' on a Server Tag sticker (small labels marked S1, S2, etc.) and stick it to the front face of the chassis. | ||
− | ** Print the printme, write the number from the Server Tag in the upper right-hand corner of the printme, and give it to your instructor. | + | ** Print the printme, write the number from the Server Tag in the upper right-hand corner of the printme, and give it to your instructor.<br><br> |
* Move the system to the Server Build KVM and run Memtest, if it hasn't already been done. | * Move the system to the Server Build KVM and run Memtest, if it hasn't already been done. | ||
* Consult your Instructor for a new project! | * Consult your Instructor for a new project! | ||
<noinclude>[[Category:Server_Build]]</noinclude> | <noinclude>[[Category:Server_Build]]</noinclude> |
Revision as of 14:21, 16 May 2012
Preliminaries
Check for blown caps - Examine all of the capacitors
Check battery - Confirm that the CMOS battery is at least 3 volts
Boot Process - Ensure that the server boots properly in the following ways:
- Boots from CD - use an Ubuntu Live CD, leave Ubuntu running for next step
- Boots automatically after power loss - while still in Ubuntu from the previous step, unplug all power cords (and the keyboard for the next step) from the server to simulate a sudden power loss. It should reboot automatically - if not, check BIOS settings.
- Boots without keyboard - the server may report a "Keyboard failure" error - this is okay as long it boots successfully without human intervention, such as "press key X to continue..."
RAID & LVM Setup (Build ONLY)
Install Debian Squeeze - Boot to network and install Debian Squeeze to local disks, choose hostname, leave domain name as “fglan”
Setup Software RAID
Partition Disks:
- Create small partition (400-500M) on each device
- primary partition at the beginning of the drive
- use as “physical volume for RAID”
- set as bootable
- Create large partition (all remaining space) on each device
- primary, not bootable
Setup RAID for small partitions: RAID1 (bootable) with the number of devices equal to number of disks
Setup RAID for large partitions:
- For 2-3 disks:Setup RAID1, with number of devices equal to number of disks
- For 4+ disks:Setup RAID6, with number of devices equal to number of disks
Configure LVM - configure larger RAID1 or RAID6 array as LVM volume
- Create Logical Volume Group with same name as hostname
- Select Large RAID array as LVM Volume
- create volume (4G) named root (mounted at /, ext3 filesystem)
- create volume (1G) named swap (use as swap)
- create volume (remaining) named srv (mounted at /srv, ext3 filesystem)
- Debian Wiki Guide to Software RAIDs: http://wiki.debian.org/DebianInstaller/SoftwareRaidRoot
- Wikipedia RAID article: http://en.wikipedia.org/wiki/RAID
Diagnostics & Databases
- Boot from local disk(s)
- Test USB ports (front and back),
- Test video ports (front and back),
- Test network ports - at terminal:
ifconfig eth0 up
,ifconfig eth1 up
, thentail -f /var/log/syslog
, and when you plug and unplug the ethernet cable, you should see reasonable printouts. Ctrl-C to stop thetail
command.
- QC Only: Remove any SATA/SAS drives and give them to your Instructor
- QC Only: Remove any SATA/SAS drives and give them to your Instructor
Run printme:
- Boot from network
- Select printme from the network boot menu
- Log in as guest
- Open a terminal
- Run printme
- Answer all questions and record anything else noteworthy in the notes section
Fill out the Server Specs sticker based on whether you are doing Build or QC:
- For BUILD:
- Put System ID on server specs sticker
- Number of physical processors and number of cores per processor
- Processor speed (GHz)
- Circle processor type (Xeon, Opteron, Core 2, Other)
- Total amount of included RAM
- Total number of RAM slots on board
- Number of included RAM sticks with their speed and size
- Circle type of RAM (DDR, DDR2, DDR3)
- Circle type of DIMM (ECC, FB-DIMM, etc.)
- Number of hard drive bays
- Circle hard drive bay type (IDE, SCSI, SATA, SAS)
- Number and size of included hard drives
- Record anything notable, like Hardware RAID support, in the notes section
- Do not print! Instead, put your Volunteer ID on a piece of tape on the system
- For QC:
- Confirm the accuracy of information already on the Server Specs sticker
- Number and size of included hard drives
- Circle OS installed (none if hard drives removed)
- Write the System ID# on a Server Tag sticker (small labels marked S1, S2, etc.) and stick it to the front face of the chassis.
- Print the printme, write the number from the Server Tag in the upper right-hand corner of the printme, and give it to your instructor.
- Move the system to the Server Build KVM and run Memtest, if it hasn't already been done.
- Consult your Instructor for a new project!