Difference between revisions of "HP Laserjet Printer Repair"
Jump to navigation
Jump to search
m (formatting) |
|||
Line 4: | Line 4: | ||
printer too) | printer too) | ||
==Disassembly== | ==Disassembly== | ||
− | #open up the cover, take out the toner cartridge and put it in a dark | + | #open up the cover, take out the toner cartridge and put it in a dark place |
− | place | ||
#take out the paper tray | #take out the paper tray | ||
#take off the right side skin (carefully press in two tabs) | #take off the right side skin (carefully press in two tabs) | ||
− | #drop open the back cover (if you lose the spring, you can replace it | + | #drop open the back cover (if you lose the spring, you can replace it with a Bic pen spring) |
− | with a Bic pen spring) | + | #Unscrew the 2 fuser screws and take out the fuser, check it for wrinkles and dirt |
− | #Unscrew the 2 fuser screws and take out the fuser, check it for | ||
− | wrinkles and dirt | ||
# Take off the top of the printer: | # Take off the top of the printer: | ||
## unscrew the two screws on the back of the printer FIRST! | ## unscrew the two screws on the back of the printer FIRST! | ||
Line 17: | Line 14: | ||
## press in the two tabs and gently lift the top up and tilt it right | ## press in the two tabs and gently lift the top up and tilt it right | ||
## unplug the user interface cable connecting the top to the printer | ## unplug the user interface cable connecting the top to the printer | ||
− | # Take off the rear exit transport by pressing in the two small tabs | + | # Take off the rear exit transport by pressing in the two small tabs and lifting it out |
− | and lifting it out | + | # take the top panel off the exit transport by pressing the tabs and snapping off the top |
− | # take the top panel off the exit transport by pressing the tabs and | + | # take out the top roller and treat the thicker rollers with rubber rejuvinator |
− | snapping off the top | ||
− | # take out the top roller and treat the thicker rollers with rubber | ||
− | rejuvinator | ||
# snap the top back on and save for later reinstallation | # snap the top back on and save for later reinstallation | ||
− | # Check the main drive gear in the back for broken teeth (it drives the | + | # Check the main drive gear in the back for broken teeth (it drives the fuser) |
− | fuser) | ||
# Open up the memory door | # Open up the memory door | ||
− | # Take off the small black panel on the front of the printer by | + | # Take off the small black panel on the front of the printer by pressing its tabs together |
− | pressing its tabs together | + | # Open up all internal panels and metal lids to check for paper remnants |
− | # Open up all internal panels and metal lids to check for paper | + | # take off the left skin by pressing two tabs and lowering it to the left |
− | remnants | ||
− | # take off the left skin by pressing two tabs and lowering it to the | ||
− | left | ||
# take off the right front panel with the cartridge slot in it | # take off the right front panel with the cartridge slot in it | ||
− | * be careful of the tab on the bottom of the printer as it breaks off | + | * be careful of the tab on the bottom of the printer as it breaks off very easily |
− | very easily | + | * There are two internal tabs that need to be pressed down through a hole in the right side of the printer as well. |
− | * There are two internal tabs that need to be pressed down through a | ||
− | hole in the right side of the printer as well. | ||
# If broken, take off the single sheet feed tray | # If broken, take off the single sheet feed tray | ||
− | # detach the upper half of the tray from the lower by carefully | + | # detach the upper half of the tray from the lower by carefully squeezing together the two pivot points |
− | squeezing together the two pivot points | + | # take off the horizontal metal strip (with spring clip on left) (two screws) |
− | # take off the horizontal metal strip (with spring clip on left) (two | + | # take off the bottom piece by carefully bending the plastic to sneak out the two pivot points from their sockets |
− | screws) | + | # release the spring (on the left side) from the top plastic piece and remove it |
− | # take off the bottom piece by carefully bending the plastic to sneak | ||
− | out the two pivot points from their sockets | ||
− | # release the spring (on the left side) from the top plastic piece | ||
− | and remove it | ||
==Cleaning== | ==Cleaning== | ||
*Clean off both feed rollers (large rubber wheels to pick paper) | *Clean off both feed rollers (large rubber wheels to pick paper) | ||
− | * For the bottom feed roller, press the clip to remove it and rotate | + | * For the bottom feed roller, press the clip to remove it and rotate the rubber band to bring new rubber into the worn pick area |
− | the rubber | ||
− | band to bring new rubber into the worn pick area | ||
* Blow out everything with compressed air and clean all surfaces | * Blow out everything with compressed air and clean all surfaces | ||
==Reinstallation== | ==Reinstallation== | ||
− | # Put rear exit transport back on. Slide pins into slots and click in | + | # Put rear exit transport back on. Slide pins into slots and click in two tabs |
− | two tabs | + | * don't forget to slide on the metal clip on the left side of the printer |
− | * don't forget to slide on the metal clip on the left side of the | ||
− | printer | ||
#Put front single sheet feed plastic parts back on | #Put front single sheet feed plastic parts back on | ||
#put horizontal metal strip with left side spring clip back on | #put horizontal metal strip with left side spring clip back on | ||
Line 82: | Line 62: | ||
#- Press "next/index button" until "self test" appears | #- Press "next/index button" until "self test" appears | ||
#- Press "Enter" to run the self test and print out an info page | #- Press "Enter" to run the self test and print out an info page | ||
− | #- Leave test page in output tray and put printer in store (LJ4 = $70, | + | #- Leave test page in output tray and put printer in store (LJ4 = $70, 4plus/4Mplus = $80?) |
− | 4plus/4Mplus = $80?) | ||
==Most common problems== | ==Most common problems== | ||
− | * rubber rollers on exit transport are shiny and smooth (z-fold paper | + | * rubber rollers on exit transport are shiny and smooth (z-fold paper jams) |
− | jams) | ||
* main drive gear running the fuser is broken or missing teeth | * main drive gear running the fuser is broken or missing teeth | ||
* the front pick roller is dirty or smooth | * the front pick roller is dirty or smooth | ||
* the lower feed roller is dirty or smooth (rotate the rubber band) | * the lower feed roller is dirty or smooth (rotate the rubber band) |
Revision as of 16:47, 2 July 2005
HP Laserjet 4 and 5
Cleaning up HP LJ 4, 4plus and 4Mplus printers (could be for LJ5 printer too)
Disassembly
- open up the cover, take out the toner cartridge and put it in a dark place
- take out the paper tray
- take off the right side skin (carefully press in two tabs)
- drop open the back cover (if you lose the spring, you can replace it with a Bic pen spring)
- Unscrew the 2 fuser screws and take out the fuser, check it for wrinkles and dirt
- Take off the top of the printer:
- unscrew the two screws on the back of the printer FIRST!
- unscrew the one screw on top
- press in the two tabs and gently lift the top up and tilt it right
- unplug the user interface cable connecting the top to the printer
- Take off the rear exit transport by pressing in the two small tabs and lifting it out
- take the top panel off the exit transport by pressing the tabs and snapping off the top
- take out the top roller and treat the thicker rollers with rubber rejuvinator
- snap the top back on and save for later reinstallation
- Check the main drive gear in the back for broken teeth (it drives the fuser)
- Open up the memory door
- Take off the small black panel on the front of the printer by pressing its tabs together
- Open up all internal panels and metal lids to check for paper remnants
- take off the left skin by pressing two tabs and lowering it to the left
- take off the right front panel with the cartridge slot in it
- be careful of the tab on the bottom of the printer as it breaks off very easily
- There are two internal tabs that need to be pressed down through a hole in the right side of the printer as well.
- If broken, take off the single sheet feed tray
- detach the upper half of the tray from the lower by carefully squeezing together the two pivot points
- take off the horizontal metal strip (with spring clip on left) (two screws)
- take off the bottom piece by carefully bending the plastic to sneak out the two pivot points from their sockets
- release the spring (on the left side) from the top plastic piece and remove it
Cleaning
- Clean off both feed rollers (large rubber wheels to pick paper)
- For the bottom feed roller, press the clip to remove it and rotate the rubber band to bring new rubber into the worn pick area
- Blow out everything with compressed air and clean all surfaces
Reinstallation
- Put rear exit transport back on. Slide pins into slots and click in two tabs
- don't forget to slide on the metal clip on the left side of the printer
- Put front single sheet feed plastic parts back on
- put horizontal metal strip with left side spring clip back on
- clip the two plastic pieces back together
- snap the small black front cover back on
- snap the front right panel (with cartridge slot) back on
- reinstall left panel. Put base tabs in and snap into place
- screw the memory door shut
- Put the top back on:
- connect the user interface panel cable
- snap the top down onto the printer
- add one screw in front-top and two screws in back
- Re-install fuser with two screws
- close the back cover
- re-install right side skin with tabs in bottom and snap into place
- put the toner cartridge back in and close the top toner door
Testing
- - Put printer into offline mode (press online/offline button)
- - Press menu button until "test menu" appears
- - Press "next/index button" until "self test" appears
- - Press "Enter" to run the self test and print out an info page
- - Leave test page in output tray and put printer in store (LJ4 = $70, 4plus/4Mplus = $80?)
Most common problems
- rubber rollers on exit transport are shiny and smooth (z-fold paper jams)
- main drive gear running the fuser is broken or missing teeth
- the front pick roller is dirty or smooth
- the lower feed roller is dirty or smooth (rotate the rubber band)