As-Is Checklist

From FreekiWiki
Revision as of 09:38, 26 September 2013 by Aradan (talk | contribs)
Jump to navigation Jump to search

Note: A version of this guide in LibreOffice format is available on the wiki at this link. That version is strongly recommended for printing.

The laptop you are inspecting has been designated an “AS-IS” laptop. This means it is either slightly below our minimum Spec Level or it has issues that prevent us from being able to offer it with a warranty. In other words, it's not quite good enough to go through the Build process, but might still be of use to someone. We ensure basic functionality, but do not perform the more detailed tests of the Build and Quality Control processes. Thank you for your help!


  • Learn to use the Laptop Build Room tools to identify hardware components.
  • Practice installing and removing hardware.
  • Figure out an organizational strategy that works for you when disassembling and reassembling parts.
  • Learn POST troubleshooting for laptops.

1. Data Security Check

We are responsible for securely wiping or destroying any data storage device that is donated to Free Geek. This is the most important step in this process. In most cases this means removing hard drives from computers so the data can be wiped, but keep an eye out for other kinds of data storage devices.

Check for Hard Drives
☐ Separate any hard drive caddies and adapters from the hard drive.
☐ Tape them (along with their screws) back inside the hard drive bay. These should stay with the system unless your instructor needs them for parts.
☐ If a hard drive or other storage device is found, it should always be given to your instructor.
☐ Some laptops (especially larger models) may have two hard drive bays, so don't stop looking just because you've found one.

Check for Other Storage Devices
☐ Check the Optical Drive for disks.

  • You can manually open the drive by pusing a paper clip into the small quick-release hole in the drive faceplate.

☐ Look inside and around the chassis for other less common storage devices, such as:

  • 1.8” or other small-form-factor hard drives
  • Mini PCI, mini-PCIe, or mSATA solid state drives (SSDs)
  • SD cards or MemorySticks
  • SIM cards (usually under the battery)
  • Floppy disks
  • PCMCIA (PC Card slot) hard drives


2. Physical Evaluation

Take a close look at the laptop you are evaluating. Inform your instructor if you find any of the following:
☐ Floppy Drive
☐ Missing cover plates on the bottom of the laptop
☐ Missing Battery
☐ Missing Optical Drive
☐ Missing keyboard or individual keys
☐ Cracked or broken hinges
☐ Cracks, discoloration, scratches, or marks on any surface
☐ Evidence of liquid spills or oxidation residue
☐ Dirt, dust, cat hair and/or grime above and beyond what can be cleaned
☐ Damaged ports or power jack (look very closely)
☐ Visible screen damage (look for hairline cracks or splatter marks inside the screen)

Stop here and check with your instructor if the laptop has any of these issues; they may have you go through the Recycling process instead. Check with your instructor for confirmation.

3. Find an appropriate AC adapter

For an AC adapter to power the device correctly, it must:

  • Match the input voltage (V) of the laptop exactly.
  • Match or exceed the recommended amperage (A).
  • Have a plug that fits into the laptop snugly and provides power.

☐ Find the input voltage and amperage listed on the laptop. This may be printed on the back of the laptop, or on the chassis under the battery.
☐ Find an AC adapter that matches the voltage and amperage listed on the laptop. You will be looking in the output section printed on the AC adapter, which should look like this:

INPUT:  100-240V~1.9A
OUTPUT: 16V  4.5A 

AC adapters are sorted in bins by voltage, amperage, and brand; the bins are color-coded by brand.


☐ Try turning the machine on.

  • If the system loads the BIOS splash screen, you can proceed to next step.
  • If the system does not boot, or appears to have screen or video problems, use sections 1 and 2 only in the Laptop POST Troubleshooting Guide in Appendix (A-1).
    • If an AS-IS laptop fails to POST or has video or screen problems, it should be recycled according to the Laptop Recycling Guide. Check with your instructor for confirmation.

5. Determine specifications

Identify the Hardware
☐ Boot into BIOS.
☐ Find the section with system hardware information.

  • Note the CPU type and speed.
  • Note the amount of RAM installed.

☐ Add or remove RAM as needed until the laptop has 1-2 GB total. Only use 1 GB sticks or smaller in an AS-IS laptop.

☐ If no hardware information is available in BIOS, find the section for setting boot options. Set the following boot order:

First:    Optical Drive
Second:   Hard Drive
Third:    Network Device (also called LAN, Onboard NIC, or PXE)
  • Disable or ignore other devices.

☐ Save changes and exit BIOS.
☐ Plug in an ethernet cable from the workbench.
☐ The laptop should now automatically boot to the Network Boot Menu.
☐ From the Network Boot Menu, select Laptop Build → CPU Lookup. The CPU Lookup tool should load, detect the CPU hardware, match it to an entry in our database, and output key details about the CPU.
☐ Write down the following details:

  • CPU type (e.g. Celeron M, Pentium M, Core Duo, Mobile Sempron, etc.)
  • CPU clock speed in GHz (gigahertz)

Refer to the the Laptop Specs Guide in Appendix (A-6) or check with your instructor if you have difficulty locating information about the hardware.

6. AS-IS Sticker

Get an AS-IS sticker from the clipboard, stick it to the lid of the laptop, and use the information gathered in the previous steps to fill in these fields:
☐ CPU type
☐ CPU clock speed in GHz
☐ RAM amount
Leave all other fields blank

7. Final Steps and Sign-Off

Although we no longer remove Windows license keys from laptops that go through the full Build process, we are still removing them from AS-IS laptops only.

☐ Remove any Windows sticker (including the license key sticker).
☐ Remove any note or sticker identifying the previous owner or with personal information.
☐ Make sure the laptop is completely reassembled.
☐ Give the laptop a quick cleaning with a rag. Don't go too crazy.
☐ Ask your instructor to sign off on the laptop, then put it in the AS-IS bin on the cart.
☐ Check with your instructor for your next task. Thank you for helping!