Difference between revisions of "Bluetooth headset testing"
Jump to navigation
Jump to search
(Edited 'Charging the Device' & 'Pairing the Device') |
|||
(5 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
+ | {{migrated}} | ||
+ | [https://docs.google.com/document/d/12N6BHTQAJOUIxAzX8bm0bedd7HiRyYK67hjwL57_IlY/edit?usp=sharing link] | ||
+ | |||
==Bluetooth Testing== | ==Bluetooth Testing== | ||
[[User:Ragnabomb|Ragnabomb]] 19:13, 26 May 2010 (UTC) | [[User:Ragnabomb|Ragnabomb]] 19:13, 26 May 2010 (UTC) | ||
Line 13: | Line 16: | ||
|- | |- | ||
| Charge the Device || | | Charge the Device || | ||
− | *Find the correct charger for all of the devices you want to test. '''Match by connector type | + | *Find the correct charger for all of the devices you want to test. '''Match by connector type AND voltage''' the amperage must be the same or higher as listed on the device. |
*Try to charge as many devices as you can at a time. | *Try to charge as many devices as you can at a time. | ||
Line 28: | Line 31: | ||
*At 'Device Search>Device type', select 'Headphones, headsets, and other audio devices'. | *At 'Device Search>Device type', select 'Headphones, headsets, and other audio devices'. | ||
*The program will search for your device. When (or if) it successfully locates it, hilite it and click 'Forward'. | *The program will search for your device. When (or if) it successfully locates it, hilite it and click 'Forward'. | ||
− | |||
*At 'Device Setup' wait for setup to complete. | *At 'Device Setup' wait for setup to complete. | ||
*At 'Setup Complete' click 'Close'. | *At 'Setup Complete' click 'Close'. | ||
Line 34: | Line 36: | ||
|- | |- | ||
| Configure Device for Input/Output || | | Configure Device for Input/Output || | ||
− | * | + | *Go into System>Preferences>Sound. |
*Go to the 'Input' and 'Output' tabs and highlight the bluetooth device that you have paired under 'Choose a device for input/output', this sets the bluetooth device to be used as a headphone/microphone. | *Go to the 'Input' and 'Output' tabs and highlight the bluetooth device that you have paired under 'Choose a device for input/output', this sets the bluetooth device to be used as a headphone/microphone. | ||
|- | |- | ||
Line 40: | Line 42: | ||
If everything is working correctly you should hear your test clip played back to you through the headset. | If everything is working correctly you should hear your test clip played back to you through the headset. | ||
|- | |- | ||
− | | Affix sticker || Initial a 'Tested by' sticker and stick it to the device | + | | Affix sticker || Initial a 'Tested by' sticker and stick it to the charger. Bluetooth device & charger go together to the store, use a rubber band. Once you are done testing devices make sure to place them in the box to go to the store. |
|} | |} | ||
[[Category:Hardware Testing]] | [[Category:Hardware Testing]] | ||
[[Category:Howto]] | [[Category:Howto]] | ||
− |
Latest revision as of 15:20, 5 July 2014
This page has been migrated to a document on Free Geek's Google Drive. Information remaining behind may no longer be relevant. MIGRATOR: When you have tagged this page as migrated, (Link to new page immediately below.) |
Bluetooth Testing
Ragnabomb 19:13, 26 May 2010 (UTC)
Bluetooth devices take very little to test but often require research to find the particulars on each device. Note that if it ever asks you for a 'code' or 'pin' try '0000' or '1234', these are both default pins for bluetooth devices.
|