Difference between revisions of "Front Panel Motherboard Pin-outs"
Dunstvangeet (talk | contribs) |
|||
| (7 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | {{migrated}} | ||
| + | |||
| + | [https://docs.google.com/a/freegeek.org/document/d/1X4md91tcZYmgz6ZLIRCcccBwUgnKXElPRGFJE-e8Ils/edit?usp=sharing Link] | ||
| + | |||
These are pinout settings for the standard Front Panel on Motherboards. | These are pinout settings for the standard Front Panel on Motherboards. | ||
| Line 41: | Line 45: | ||
==Standard Front Panel Power== | ==Standard Front Panel Power== | ||
| − | Front Panel Power can come in all sorts of ways. Best way is to look on the board. However, on some boards, there are is no writing. In that case, first try this output | + | Front Panel Power can come in all sorts of ways. Best way is to look on the board. However, on some boards, there are is no writing. In that case, first try this output. |
| − | {| | + | {| border=1 |
| − | | colspan=2 | | + | | colspan=2 align=center | Power LED || colspan = 2 align=center | Power Switch || align=center | KEY |
|- | |- | ||
| − | | width=80 align=center | 2 || width=80 align=center | 4 || width=80 align=center | 6 || width=80 align=center | 8 || width=80 align=center | 10 | + | | width=80 align=center | 2 || width=80 align=center | 4 || width=80 align=center | 6 || width=80 align=center | 8 || width=80 align=center bgcolor=#000000 | 10 |
|- | |- | ||
| align=center | 1 || align=center | 3 || align=center | 5 || align=center | 7 || align=center | 9 | | align=center | 1 || align=center | 3 || align=center | 5 || align=center | 7 || align=center | 9 | ||
|- | |- | ||
| − | | | + | | colspan=2 align=center | HD LED || colspan=3 align=center | Reset Switch |
|} | |} | ||
| + | If this doesn't work, try starting with the Power Switch, and put it in every combination until it works. Then do the same with the HD LED, Power LED, and the reset switch. | ||
| + | |||
| + | [[Category: Build]] | ||
Latest revision as of 13:36, 18 April 2014
 This page has been migrated to a document on Free Geek's Google Drive. Information remaining behind may no longer be relevant. MIGRATOR: When you have tagged this page as migrated, (Link to new page immediately below.) |
These are pinout settings for the standard Front Panel on Motherboards.
USB Internal
USB is made up of two 4-pin connectors, with a 5th throw away pin to make sure you don't plug it in backwards. The Pin-out information is the following:
| VCC 1 | Data- 1 | Data+ 1 | Ground 1 | Not Used |
| 2 | 4 | 6 | 8 | 10 |
| 1 | 3 | 5 | 7 | |
| VCC 2 | Data- 2 | Data+ 2 | Ground 2 | Key |
IEEE 1394 (Firewire) Internal
IEEE usually looks exactly the same as the USB on the inside. Look for writing on the Motherboard to indicate whether it is USB or Firewire.
| TPA- | GND | TPB- | +12V | S-Ground |
| 2 | 4 | 6 | 8 | 10 |
| 1 | 3 | 5 | 7 | |
| TPA+ | GND | TPB+ | +12V | Key |
Front Panel Audio
The front panel audio usually comes in either a 10-pin or a 14-pin Connection. Either way, most of them are hooked up the same way. If there is no front panel audio on the chassis, There must be jumpers between 5 and 6, and 9 and 10, or the back audio may not work.
| AUD Ground | AUD Ground | FP RET R | Key | FP RET L |
| 2 | 4 | 6 | 10 | |
| 1 | 3 | 5 | 7 | 9 |
| Mic In | Mic Power | FP OUT R | AUD +5V | FP OUT L |
Standard Front Panel Power
Front Panel Power can come in all sorts of ways. Best way is to look on the board. However, on some boards, there are is no writing. In that case, first try this output.
| Power LED | Power Switch | KEY | ||
| 2 | 4 | 6 | 8 | 10 |
| 1 | 3 | 5 | 7 | 9 |
| HD LED | Reset Switch | |||
If this doesn't work, try starting with the Power Switch, and put it in every combination until it works. Then do the same with the HD LED, Power LED, and the reset switch.