Difference between revisions of "Motherboards"

From FreekiWiki
Jump to navigation Jump to search
(Spelling / Grammar)
(removed categories from page marked {{delete}})
 
(18 intermediate revisions by 6 users not shown)
Line 1: Line 1:
 +
{{delete}} replaced with new page [[MotherBoard Testing]]
 +
 
== Boards We Like to Test ==
 
== Boards We Like to Test ==
 
* [[wikipedia:Socket 423|Socket 423]]
 
* [[wikipedia:Socket 423|Socket 423]]
 
* [[wikipedia:Socket 462|Socket 462]]
 
* [[wikipedia:Socket 462|Socket 462]]
−
* [[wikipedia:Socket 478|Socket 478]]
+
* [[wikipedia:Socket 478|Socket 478]]  
 
* [[wikipedia:Socket 479|Socket 479]]
 
* [[wikipedia:Socket 479|Socket 479]]
 
* [[wikipedia:Socket 603|Socket 603]]
 
* [[wikipedia:Socket 603|Socket 603]]
 
* [[wikipedia:Socket 754|Socket 754]]
 
* [[wikipedia:Socket 754|Socket 754]]
 +
* [[wikipedia:Socket 775|Socket 775]]
 
* [[wikipedia:Socket 939|Socket 939]]
 
* [[wikipedia:Socket 939|Socket 939]]
 
* [[wikipedia:Socket 940|Socket 940]]
 
* [[wikipedia:Socket 940|Socket 940]]
 +
* [[wikipedia:Socket AM2|Socket AM2]]
  
 
== How to Test ==
 
== How to Test ==
−
*Secure MoBo to plate, ensuring the risers are not grounding out the board.
+
* Grab a Motherboard, check for visual defects (blown caps, mutilated components)
−
*Connect
+
* Secure MoBo to plate, ensuring the risers are not grounding out the board.
−
**IDE II
+
* Test battery,
−
**Floppy
+
* Add a tested processor and a fan for that MoBo
−
**Power Supply
+
* Add tested memory
−
**PCI Video Card
+
* Attempt to post
−
***Some cases might call for testing
+
** Connect the minimal things needed to post (power, keyboard, video, etc).
−
****RAID
+
** If it does not post replace the processor (do an internet search with the socket number to find the range the range of compatible processors).
−
****SATA
+
* Power down, then attach:
−
*Once started change the boot order in BIOS to boot from each device.
+
** Imaged hard drive to IDE1 (Primary)
−
*Note
+
** CD Drive to IDE2 (Secondary
−
*The Floppy Drive should have Memtest floppy disk all ready in it.
+
** Floppy Drive to FD controller
−
*The CD Drive should have Knoppix in it.
+
** Peripherals (mouse, keyboard, Video)
−
*Once the PCI video has been tested, test the AGP slot with the Universal Voltage AGP card.
+
* Boot into BIOS
−
 
+
** Set the clock and date.
−
*there is some knowledge needed to test motherboards properly.
+
** Change the boot order to be CD Rom first , Hard Drive second, Floppy disconnect.
−
 
+
* Boot to Memtest, Let it run for a minute. Test all memory slots. (The memtest program is a boot option on the hard drive)
−
here is a list of commands I think one should know. (besides the basics)
+
* Boot up to Operating System
−
 
+
** Check that the mouse and keyboard work.
−
*mount(8)
+
** If you have on board video check that it works.
−
  You use this command to mount devices. Like a hard drive or a floppy disk.
+
** Test all the USB ports with a mouse.
−
  Some knowledge of the /dev directory is needed but not a whole lot. have fun.
+
** If you have on board sound play a audio cd, if not then open a terminal and run basiccheck -m
−
       
+
** Open terminal and run stress-test.
−
            mount /dev/fd0 /place/in/file/system/to/mount/device
+
** Test all card slots by plugging in a video card, turn on computer, if you get a screen turn off computer and repeat with all slots.
−
                                    ^
+
*Some cases might call for testing
−
                                  /|\
+
**SATA
−
                                    |  this is most of the time /mnt/floppy
 
−
  if you type " umount /dev/fd0 " after that command you would unmount the device from the
 
−
  file system.
 
−
 
 
−
*dmesg(8)
 
−
  This is a very nifty command. It tells all. As in it tells every thing about your
 
−
  system (well most of the time). it is used with the command less(1) a lot. At least with me
 
−
  or grep.
 
−
 
−
          Try and type:
 
−
                        dmesg | less
 
−
            or
 
−
                        dmesg | grep hdc  # to see what device is attached to /dev/hdc
 
−
  TRY IT it's fun.
 
−
 
 
−
==So You have all the parts and a Knoppix disk.==
 
−
 
 
−
*First make sure everything is plugged in yeah.
 
−
 
 
−
  If you have never booted from a live linux cd or Knoppix now is the time to learn.
 
−
  After the system POSTs you will be met by a command prompt it will say somewhere
 
−
  to press F2 or F3 for a cheat sheet, feel free to do so. or you could just type:
 
−
     
 
−
        knoppix 2
 
−
 
−
  then enter. That command will boot the system into run level 2
 
−
  which is short for start the system without the X server.
 
−
 
 
−
* next check if the system can see all the hardware and anything else you plugged into it.
 
−
 
 
−
  hint: use dmesg
 
−
 
 
−
*well, what if?
 
−
 
 
−
What if what!! It should work right RIGHT! Not all the time is right sometimes It just doesn't work.
 
−
 
 
−
hint number two: check for bad capacitors. what are bad caps?? well google it or ask Dave Haskins ;)
 
−
, but most if the time if it doesn't work then it just doesn't work.
 
  
 
==HAVE FUN==
 
==HAVE FUN==
−
 
−
[[Category:Hardware Testing]]
 

Latest revision as of 11:46, 1 December 2010

deletion

This page has been requested to be deleted.
If you disagree, discuss on the talk page.
Whenever possible, could an Admin please remove this page? 

replaced with new page MotherBoard Testing

Boards We Like to Test

How to Test

  • Grab a Motherboard, check for visual defects (blown caps, mutilated components)
  • Secure MoBo to plate, ensuring the risers are not grounding out the board.
  • Test battery,
  • Add a tested processor and a fan for that MoBo
  • Add tested memory
  • Attempt to post
    • Connect the minimal things needed to post (power, keyboard, video, etc).
    • If it does not post replace the processor (do an internet search with the socket number to find the range the range of compatible processors).
  • Power down, then attach:
    • Imaged hard drive to IDE1 (Primary)
    • CD Drive to IDE2 (Secondary
    • Floppy Drive to FD controller
    • Peripherals (mouse, keyboard, Video)
  • Boot into BIOS
    • Set the clock and date.
    • Change the boot order to be CD Rom first , Hard Drive second, Floppy disconnect.
  • Boot to Memtest, Let it run for a minute. Test all memory slots. (The memtest program is a boot option on the hard drive)
  • Boot up to Operating System
    • Check that the mouse and keyboard work.
    • If you have on board video check that it works.
    • Test all the USB ports with a mouse.
    • If you have on board sound play a audio cd, if not then open a terminal and run basiccheck -m
    • Open terminal and run stress-test.
    • Test all card slots by plugging in a video card, turn on computer, if you get a screen turn off computer and repeat with all slots.
  • Some cases might call for testing
    • SATA

HAVE FUN

Retrieved from "http://wiki.freegeek.org/index.php?title=Motherboards&oldid=53281"